Playstation 3 - Modchip Central. Infectus Team is the most advanced programmer for every ProgSkeet NAND / NOR / EEPROM USB Programmer or the ARGON and INFECTUS. PS3 3.6x Downgrade Tutorial (256Mb NAND Only). And you’ve got already designed your Infectus with PS3 DUAL NAND. Locate the libusb folder and install the. Slim type ps3’s CECH-20xx(OK To Downgrade) NOR = Teensy++ 2.0 / Progskeet / E3 Flasher CECH-21xx (OK To Downgrade) NOR = Teensy++ 2.0 / Progskeet / E3 Flasher CECH-25xxA or B (with date code [0C] [0D] [1A] are known to be ok) NOR = Teensy++ 2.0 / Progskeet / E3 Flasher ALL THE REST (DOUBLE CHECK THIS with MinVerChk from AS SOME CANNOT BE DOWNGRADED) CECH-30xx (CANNOT Downgrade) CECH-40XX (CANNOT Downgrade) This information was taken from & & Requied tools for downgrading 1. A NAND or NOR Programmer. The ps3 slim A blue Phillips screw is hidden beneath the screw cover. Remove this screw. Next, remove the hard drive cover. The drive enclosure has a metal pull tab attached to it. Pull on it to release the drive from the bay. Remove the three T8 security Torx screws on the underside of the PS3 slim. Remove the warranty sticker (there are ways to remove these without damaging the sticker. Using a hair dryer (but you can warp the casing if you get it too hot) and sticky stuff remover (yes that’s what it is called) but if you put too much on it can get into the system & you don’t want that) Seven Phillips screws need to be removed from the bottom. The rubber pad on the front-right corner of the PS3 has no screw hidden underneath. Remove the other 3 and the 4 plastic screw covers. You should be able to simply lift these off with your finger nail. Flip the PS3 over & remove the top case lifting the rear first (like opening a door) Disconnecting two power supply cables in red and two screws in blue Removing the power supply. Remove the inlet power connector Unplug the fan Remove the bdvd drive flat cable. Can be lifted with a finger nail & Remove the screw The Blue-ray drive comes right out. Pull out the power panel’s flat cable remove 3 black in red and 2 silver screws in blue the logic board lifts free of the chassis Unscrew 5 silver screws in red securing the shield do not remove the 2 black screws in yellow & Remove The screws for the two identical brackets in blue remove the metal shield from the logic board. And in red you can see your board type lift the logic board it will feel like its glued down but lift till there is pressure and wait as it will slowly un stick with a “pop” take note of where the heat transfer pads are in red. They may be stuck to components on the logic board.& clean the old heat transfer paste from these areas with alcohol wipes in blue clean the two chips with alcohol wipes in blue & you will notice your NOR chip in red a close up of the NOR chip (you need to either jot down every detail from the chip or its better to take a clear photo and check you can zoom in and read it) all the old heat transfer paste removed place a line of heat transfer paste to both chips using a credit card spread the compound over both chips going top to bottom, left to right, bottom to top, and right to left. Until it’s on evenly. Then put the logic board back onto the bottom heat shield (the one you just cleaned) place 2 folded pieces of card in the areas shown screw the two identical brackets back in place insuring they are sat on the card NOT touching the logic board. Plug in the fan (DO NOT MISS THIS STEP) re attach the power brick connect the wires in red and screw it down in blue flip it back over and your all set Phat Strip Down. The 'phat' ps3 On the left side of the console you will see a few rubber feet. The first screw to be removed is underneath the rubber foot circled in red in the picture below. The foot can be pried out with a small screw driver. Then underneath is a Torx security screw. Once the screw is removed, slide the top of the case to the left. It may require a bit of force to slide if you’re opening the console for the first time. After the top slides as far as it will go, lift the top and it should come off as seen in the picture below: After the top is off, there will be another cover. You will need to remove the 7 long screws circled in red. After the 7 screws are removed, gently lift up the back corners of the top half of the console.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2019
Categories |